K8N-E RAID DRIVER DOWNLOAD

I want to configure a raid 0 array using two IBM gb sata drives, problem is as follows: K8N-E raid setup many thanks for the quick response. If I skip all the floppy files then it just cycles round to start the setup over again. Raid-1 allows you to mirror the data on two drives. Using the site is easy and fun. These settings are for using the Dual Raid.

Uploader: Tanris
Date Added: 12 November 2004
File Size: 13.66 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 71995
Price: Free* [*Free Regsitration Required]

So at the moment I am completely lost – I dont know what to try next, [go on holiday might be a good idea] however any suggestions would be most gratefully received, anything at all that might help point me in the right direction.

ShieldSquare reCAPTCHA Page

Several functions may not work. Please log in to reply. I’ve been trying for three days now and all I have got is grey hair! K8N-E raid setup You have to load the Raid and storage controller drivers. What happens to my C drive?

It is not possible to load an os directly onto raif sata raid array [ide yes – sata no] 2. Using the site is easy and fun.

Raid 0 and Raid 1. If I disable raid in bios, put a single disk on either controller then windows will install on that disk with no problems. K8N-E raid setup Partial success!

Don’t know if that detection problem is only in bios at boot up, though it might be intermitent, since the question says “sometimes”. That means if one drive dies, the other drive will contain the correct up-to-date data and you will have no downtime. During set up with the Nvidia controller in use there are two drivers on the floppy, raid and then controller, when selected both appear to load in turn, by that I mean that there is audible and o8n-e indication from the floppy, and at the bottom of the screen it says ‘loading nvraid.

  MINOLTA 1380MF WINDOWS 7 DRIVER

What is anyone else using for the controllers.

ASUS K8N-E – motherboard – ATX – Socket 754 – nForce3 250Gb Series

Using the Nvidia controller with the bios raid parameters set as per the manual press f10 after post and the drives are recognised and can be configured as raid 0. The time now is With raid-0 you store data across all the drives in the array.

In the Chipset category of the Bios under the sub category of OnBoard Device you have enable the Raid option Rom, then enable the third master and fourth master? K8N-E k88n-e setup Might try another floppy disk. IF they are not included in the Raid they should be disabled. Remember me This is not recommended for shared computers.

Which set of Drivers are you choosing first? Thread Tools Show Printable Version.

Are you using the “Primary Slave” in a Raid array? 8kn-e far as 1 goes I have to agree with him as I spent 5 days trying to do it with no success, the drivers should be loaded through an os is what he said. I spoke to a tech at asus support and got the following info: You would be surprized at what type of errors could show up due to a little memory error. Start WinXP pro setup from cd, at prompt load both Daid raid drivers [leave floppy in]setup carries on – recognises the drive – formats – then at windows install it stops with ‘cannot load file nvraid.

  ECS 945GCT M V2.0 LAN DRIVER DOWNLOAD

This is said to increase performance, but there is an inherint security risk, as if one drives dies, the whole array will be broken and you will lose data. Please re-enable javascript to access full functionality. I want to configure a rwid 0 array using two IBM gb sata drives, problem is as follows: You currently have javascript disabled.

Though would not think it should affect things never know though. As for 2 my knowledge on sata is kn-e so I cant really comment.

Have you tried a Different floppy disk? If I skip all the floppy files then it just cycles round to start the setup over again.